Skip to content
Home
READY PLASTER

READY PLASTER

READY PLASTER
READY PLASTER
READY PLASTER
READY PLASTER
READY PLASTER
READY PLASTER

BREATHABLE

(High Porosity, High Permeability)

In our view, sustainable structures should be designed to breathe, just as we do. If a building envelope is too air tight, moisture can become trapped inside. One of the outstanding benefits of using Ready Plaster. Ready Plaster allows you to build permeable wall systems, eliminating standing condensation. A Ready Plaster structure “breathes” and enabling moisture to evaporate. If you’re building in a damp or tropical climate, preventing moisture damage is especially critical. Use of Ready Plaster will enable you to build structures that prohibit moisture, bacteria,
mold and mildew from forming within the building envelope.

ENERGY EFFICIENCY

Ready Plaster offer thermal comfort and protection, It supports in energy saving system.

MOISTURE RESISTANCE

Ready Plaster can tolerate damp and sea-side applications that would normally de-laminate acrylic-based plasters, latex-based paints and Gypsum-based plasters.

LOW THERMAL CONDUCTIVITY

Ready Plaster plays a pivotal role in creating optimal thermal protection. 

WORKABLE

It is supplied in powdered form; it is pretty much the same as mixing and working with modern cement. Mixed to the right consistency, Ready Plaster mortar & plaster are beautiful materials to work with.

HYGIENIC

Of many issues at hand with non-sustainable structures, Indoor Air Quality is a critical concern. Artificial, chemical-based structural paints and plasters have been cited as a major factor in releasing poisonous air pollutants and airborne bacteria. When a structure is properly designed, Ready Plaster eliminate VOCs, mildew, mold, and bacterium while creating huge advantages to the structural elements of the building. Using Ready Plaster, places you directly in line with truly sustainable building practices.

HOW TO USE

The surface need to be cleaned and made free from grease and loose particles. The porous and absorbent substrates need to be pre-wetted prior to application of READY PLASTER to prevent premature loss of water from the plaster. This will ensure that thin layer can be applied without cracking problems and proper cement hydration and adherence of the mortar to the substrate is attained.

  • Use 7-9 liters of water approximately for 40 kg READY PLASTER. Mix the clean water with READY PLASTER for 4-5 minutes with hand or stir better with mechanical mixer to achieve a good consistency. Do not over mix.
  • Allow mixture to stand for 5 minutes for additives to dissolve and after re-mix, plaster is ready for use.
  • Apply plaster to the substrate, using some pressure while finishing with a steel trowel or wooden float to ensure optimum bonding of the plaster to the substrate surface.
  • READY PLASTER can be either hand- applied or spray machine-applied.
  • READY PLASTER can be used in exterior and interior surface.

PACKAGING 40kg HDPE bags.

STORAGE Dry and protected.

Comparison with conventional method of plastering

Parameter
Ready Mix Plaster
Conventional Method
Application time
Fast application
Not possible
Quality
Consistent quality due to computerized process
Manual mixing, hence not possible to test every batch
Shrinkage cracks
Minimum shrinkage cracks
Significantly high shrinkage cracks
Handling and storing
Minimum shrinkage cracks
Difficult to keep stock of different material
Wastage
No wastage
High wastage
Efflorescence
Negligible
Observed in many cases
Sand
Graded
Not graded
Rebound loss
Minimum
High due to non-gradation & bigger sand particle size

TECHNICAL DATA

Property
Typical Results
Colour
Cement Gray
Pot Life
2 hrs
Maximum grain size
2.5 mm
Bulk Density
1.5
PH
Alkaline
Coverage
15-20 Sqft/40 Kg bag at thickness of 12-15 mm
Curing
Curing required 6-7 Days
Recommended mixing ratio
7-9 Ltrs water/bag

QUALITY ASSURANCE

This product undergoes third party and in-house monitoring, using a quality management system which conforms to the current international standard E N I S O 9 0 0 1 and the environmental standard ISO 14001.

OUR PRODUCTS
OUR PRODUCTS
OUR PRODUCTS
OUR PRODUCTS
OUR PRODUCTS
OUR PRODUCTS
OUR PRODUCTS

BLOCK JOINTIN MORTAR

Block Joint is a versatile thin jointing material for laying ACC blocks, fly ash bricks, concrete etc.

READ MORE